Instek PEL-5005G-1200-200

Single Channel High Power DC Electronic Load, 1200V,200A,5kW

PEL5005G1200200
PEL-5005G-1200-200

Instek PEL-5005G-1200-200

Single Channel High Power DC Electronic Load, 1200V,200A,5kW

PEL5005G1200200
PEL-5005G-1200-200

The Instek PEL-5005G-1200-200 High Power DC Electronic Load can test and verify the specifications of batteries, electric vehicle chargers/charging stations and electric vehicle batteries. The turbo mode function present on this unit allows for 1.5 times the rated power or current to be used within two seconds.

  • Max Power: 5kW
  • Max Voltage/Current: 1200V/200A
  • Number of Channels: 1
  • Built-In Slow Starter for DC Load Protection
  • Single Channel High Power DC Electronic Load, 1200V,200A,5kW
  • 4U/6K High power density design also for bench testing
  • Turbo Mode Function allows 1.5 times the rated power or current to be used within two seconds
  • Turbo Mode can be used with OCP/OPP/BMS/Short Mode/Surge Mode/Hot plug-in testing
  • Flexible CC, CR, CV, CP, CV + CL, CV + PL, dynamic and short circuit operation modes
  • Surge test mode for capacitive load for current rising transient test
  • Master-slave control is up to 1 Master and 7 Slaves
  • Voltage meter display can be configured as polarity positive ("+") or Negative("-")
  • Optional Interface : GPIB, RS232, USB, LAN
  • SEQ Load Mode's programmable function allows for ultra-high-speed step changes from 0.02 to 999000 ms in CC or CP mode
  • Optional 9923 load current waveform generator to provide the battery actual discharge current waveform simulation
  • Protection function Testing for Battery BMS
  • Protection Against V, I, W, and ℃

The GW Instek PEL-5005G-1200-200 single-channel electronic load provides 1200V, 5kW. The PEL-5005G-1200-200 can test and verify the specifications of batteries, electric vehicle chargers/charging stations and electric vehicle batteries. PEL-5005G-1200-200 supports parallel connection for same voltage specification and different power models and can support up to 8 units connected in parallel to provide a maximum power of 48kW.

For the scenario of Battery Charger testing, PEL-5005G-1200-200 specifically provides four battery discharge modes, namely CV+Current Limit test mode, CV+Power Limit test mode, CC mode and CP mode. Users can choose a suitable test mode according to the test requirements.

For Battery Discharge Function, users can set the discharge cut-off voltage, discharge time, or discharge capacity (Ah) in CC or CP mode to meet the battery testing requirements.

In order to meet the verification requirements of different DUTs, PEL-5005G-1200-200 provides a variety of test functions, Surge current test mode, automated OCP, OPP test functions and 150 sets of parameter storage function. The PEL-5005G-1200-200 not only provides full power output at 1000V, but also provides 60% power output at 1200V output, which is higher than the 50% power output of other manufacturers of similar electronic loads.

High-voltage batteries or chargers directly connected to the electronic load may cause damage to the electronic load. PEL-5005G-1200-200 has a built-in slow starter, which not only protects the DC load, but also saves the user's installation cost and setting time for measurement.

More Information
BrandInstek
ConditionNEW
  • 1 - PEL-5005G-1200-200 Single Channel High Power DC Electronic Load, 1200V,200A,5kW
  • 1 - Set of Banana Plugs
  • 1 - BNC – BNC Cable, 1m
  • 1 - HD-DSUB 15PIN Parallel Wire
  • 1 - PEL-028 HANDLES U-shaped Handle (fixed to the bracket)
  • 1 - PEL-031 Rack Mount Kit
  • 1 - User Manual