Phase II PHT-6005
UCI/Dynamic Ultrasonic Portable Hardness Tester with 5kgf Manual Probe
Phase II PHT-6005
UCI/Dynamic Ultrasonic Portable Hardness Tester with 5kgf Manual Probe
The Phase II PHT-6005 UCI/Dynamic Ultrasonic Portable Hardness Tester with 5kgf Manual Probe utilizes both ultrasonic and dynamic type portable hardness testers in one unit. Both large parts and small or thin work parts down to 2mm of thickness can be tested in a non-destructive manner. Test results are delivered quickly.
- Loading Force: 5kgf
- Probe Length: 154mm
- Oscillating Probe Diameter: 3mm
- Surface Roughness Requirements: Ra < 393 μin
- 5 kgf probe for surfaces with Ra below 400µin
- Loading force: 5 kg (50N)
- Probe diameter: 22mm
- Length: 154mm
- Oscillating rod diameter: 3mm
- Surface roughness: Ra < 10um
- Requirments: (Ra < 393µin)
- Min weight of test sample: 0.3 kg (.66 lbs)
- Minimum thickness of sample: 2mm (.08 in.)
- Hardness range: HRC: 20.3- 70; HRB: 61-85.6 ; HV: 80-1599; HB: 76-618
- Tolerance: +/- 3.0% deviation of average from reference value of hardness test block with minimum of 5 tests
- Display type: LCD Color Screen w/Backlight, adjustable brightness
- Data memory: 2000 groups of measured data; 20 groups of calibration data
- Data output: USB cable (included)
- Power supply: Rechargeable Lithium Battery: Voltage-4.2V, 4800mAh
- Auto power off: After 5 minutes
- Non-Destructive hand held portable hardness tester
- Combines UCI and Leeb portable hardness testing in one state of the art device
- Test steel with min thickness of .08 in. and unlimited max thickness (other materials may have larger minimum thickness levels, depending on hardness)
- Blazing fast test results
- Rockwell, Brinell and Vickers hardness test conversions shown on display
- Large Memory w/USB Output
The Phase II PHT6005 UCI/Dynamic Ultrasonic Portable Hardness Tester with 5kgf Manual Probe impliments "Ultrasonic Contact Impedance", which is based on a 136 degree diamond at the end of a vibrating rod being depressed into the test surface at a fixed load. The difference in Ultrasonic vibration frequency is then calculated into a hardness value. The PHT-6005 UCI portable hardness tester procedure is slower than the Dynamic Impact style, however the "UCI" method of hardness testing is portable, easy and accurate. It also has its own advantages when utilized for certain testing applications. UCI portable hardness testers are not restricted to large mass items like dynamic type testers. These portable hardness testers can test metals as thin as 2mm and at a hardness value as low as 20HRC (75HB). It also excels at performing hardness tests on larger, harder metals as well. Another reason for the rise in popularity is due to the fact that the UCI method is categorized as "Non-Destructive". That translates into less scrap parts/lower mfg costs due to necessary inspections.
The Phase II PHT-6005 also implements "Dynamic Impact", which is based on the Leeb principle of portable hardness,developed by Dietmar Leeb in the 1970's. A spring loaded impact body is thrust to the test surface, effecting rebound. The speed of both the initial thrust and the rebound is measured in a non-contact mode. This is calculated as a Leeb hardness value and then automatically converted to Rockwell C, B, Brinell, Vickers and Shore Values. The PHT-6005 has effectually brought easy, fast and accurate results to portable hardness testing.
Brand | Phase II |
---|---|
Condition | NEW |
Vendor Alias | PHT-6005 |
- 1 - 5 kgf Manual Probe