Tektronix P7716
16 GHz TriMode Probe with TekFlex Connector Technology and TekConnect Interface
Tektronix P7716
16 GHz TriMode Probe with TekFlex Connector Technology and TekConnect Interface
- High bandwidth for signal fidelity: 16 GHz
- Minimal device impact:
- Thin and flexible solder tips
- High bandwidth for signal fidelity: 16 GHz
- Minimal device impact:
- Thin and flexible solder tips
- Lightweight and flexible probe cable
- Active buffer tip design for low probe loading
- Easy to connect TekFlex Connector technology:
- Pinch-to-Open accessory connector
- Versatile Connectivity: solder down tips, optional browser for handheld or fixtured probing, and coaxial input (SMA adapter)
- Probe cable and solder down tips operate over extended temperature range
- Probe and tip specific S-parameters:
- Full AC calibration of probe and tip's signal path based upon unique s-parameter models
- Unique DSP filters created for each probe and tip
- TekConnect interface for oscilloscope/probe control and usability:
- Direct control via probe buttons or from the oscilloscope's menus
- Automated control of probe settings via the oscilloscope
- Automatic recognition of the probe and tip when attached to oscilloscope
Applications
- DDR/LPDDR memory verification
- High speed serial bus debugging
- MIPI D-PHY/C-PHY/M-PHY conformance tests
- HDMI and DisplayPort compliance tests
The Tektronix P7716 16 GHz TriMode Probe with TekFlex Connector Technology and TekConnect Interface uses TekFlex connector technology, combining a high speed signal path with power and communication support for an active buffer tip in a single, easy to connect accessory connector. The TekFlex connector has a pinch-to-open design that when open requires minimal force to attach an accessory tip. When the TekFlex connector is closed, it provides a secure connection to the accessory to avoid accidental disconnections.
With the TekFlex connector, the P7716 offers a set of active probe tips with the probe's buffer amplifier only millimeters from the input connections. The short signal path enabled with the active tips provides high fidelity and a high impedance input. It also minimizes signal loss, capacitance, and additive noise.
With TriMode probing one probe setup makes differential, single ended, and common mode measurements accurately. This unique capability allows you to work more effectively and efficiently, switching between differential, single ended and common mode measurements without moving the probe's connection points.
Browser Accessory for Handheld Probing (Optional)
When you need to make a quick measurement or debug a problem, the P7716 browser accessory provides a simple to use option. With precision engineered tips that are easy to see and position accurately, the P77BRWSR handheld browser accessory enables hand or fixtured probing and is ideal for probing fine pitch components and differential traces with spacing as narrow as 0.2 mm (.008 in).
The browser's tips have a full range of compliance and are adjustable in spacing using a convenient thumb wheel. A headlight on the tip enhances visibility of the probe point and can be switched on and off as needed. The browser tips are constructed of high strength BeCu and super-ceramic resistors 1. With 16 GHz bandwidth performance, the P77BRWSR handheld browser accessory enables hand or fixtured probing with signal fidelity and convenience.
Coaxial Input (SMA) Adapter (Optional)
RF/coaxial connectors, such as SMA, are often found on test fixtures or on prototype board designs. Attaching P7716 to these on-board connectors is easy with the SMA adapter. The P77C292MM adapter allows you to connect to 2.92 mm, 3.5 mm or SMA connectors with full bandwidth and low noise. The P77C292MM adapter includes TriMode functionality enabling differential, single ended, and common mode measurements.
For compliance testing of the HDMI and DisplayPort standards, the P77C292MM and P7716 is fully supported in Tektronix' automated measurement suites for these standards. With the P77C292MM adapter attached, the P7716 can provide the DC termination voltage required by HDMI and other high-speed communication standards. The termination voltage can be set manually or automatically using voltage sense circuitry in the P7716 and covers a range of ±4 V.
Automatic Probe and Tip Identification and AC Calibration
The P7716 automatically identifies the accessory connected to the probe. When the probe and tip are attached to an oscilloscope, they are recognized and a unique DSP filter providing a calibrated response is enabled. All calibration and filter calculation is based upon a unique set of s-parameters stored in the probe and tip.
These unique filters also de-embed probe parasitics from the measurement. Creating probe and tip specific filters is critical as bandwidths increase. At high bandwidth, small variations in the signal path can lead to significant variation in frequency response which cannot be corrected using a nominal DSP filter.
The P77BRWSR (Optional) accessory extends the calibration further. As the spacing of the browser's tips is adjusted, the change in opening is automatically recognized by the probe and oscilloscope. Using the value of the tip spacing, a width specific DSP filter is used to calibrate the probe's response.
The automatic recognition of the probe and tips and the automatic filter selection eliminates the risk of manually selecting the wrong filter and improves your efficiency.Signal Fidelity
You can be confident in the signal fidelity of your measurements. The innovative new probe design uses SiGe technology to provide the bandwidth and fidelity needed today and in the future.
Country of Origin | United States |
---|---|
Brand | Tektronix |
Condition | NEW |
- 1 - Accessory Kit
- 3 - Solder-in Tips
- 1 - Magnetic Cable Holder for Strain Relief
- 1 - Certificate of Traceable Calibration
- 1 - Calibration Data Report
- 1 - User Manual
- 1 - One-Year Warranty