Tektronix TPR1000
1 GHz, Single-Ended TekVPI Power-Rail Probe with TPR4KIT Standard Accessory Kit
Tektronix TPR1000
1 GHz, Single-Ended TekVPI Power-Rail Probe with TPR4KIT Standard Accessory Kit
- Compatible with the 6 series MSO, 5 series MSO, MSO/DPO3000, MDO/DPO4000, MSO/DPO5000, DPO7000, and DPO70000 1 oscilloscopes
- Bandwidth: 2
- DC coupling mode: DC to 1 GHz
- Bandwidth:
- DC coupling mode: DC to 1 GHz
- DC reject mode: 10 kHz to 1 GHz
- Dynamic range: Up to 60 V DC, 1Vp-p AC 3
- Attenuation: 1.25x 2
- Measurement accuracy:
- DC linearity: < 0.1%
- DC offset drift: ±100 μV
- Step response long-term aberrations: ±1%
- Noise:
- < 300 μVp-p noise on 6 Series MSO (20 MHz BW Limit)
- < 1 mVp-p noise on 6 Series MSO (Full Bandwidth)
- Input impedance:
- 50 kOhm DC to 10 kHz
- 50 Ohm AC > 100 kHz
- Temperature range at tip:
- –40 to +85 °C (standard accessories)
- –40 to +155 °C (high temperature cable option)
- Offset:
- ±60 V offset range
- Offset setting error: ±2 mV max, ±0.4 μV typical
- Lowest noise power-rail probe for power integrity
- For high speed/low power, switched-mode power supply, and traditional ripple measurements markets
- With the latest 6 Series MSO oscilloscopes, power-rail probes provide lowest system noise that customers need for growing power integrity requirements
- For use with the 6 series MSO, 5 series MSO, MSO/DPO3000, MDO/DPO4000, MSO/DPO5000, DPO7000, and DPO70000 1 Series
Applications
- Probing chipsets for power rail voltage supply and control in
- automotive, industrial and consumer markets
- Probing digital power management, memory and Ethernet connectivity
- Probing noise sources on high-frequency power rails
Why Use a Power-Rail Probe?
The added functionality, higher density, and faster switching speeds of modern electronic products drive the need for lower supply voltages. Designers need to zoom-in on power rails to look for high-frequency intruder signals, measure ripple and analyze coupling effects with tighter tolerances. Oscilloscopes often don't have enough offset to shift the noise and ripple on DC rails to the center of the screen to make the needed measurements.
The TPR1000 1 GHz, Single-Ended TekVPI Power-Rail Probe provides a low-noise measurement solution (oscilloscope and probe), which is critical to not confuse the noise of the oscilloscope and probe with the noise and ripple of the DC supply being measured. The higher input impedance in the probe minimizes the oscilloscope loading effect on DC rails (50 kOhm at DC). The probes provide higher bandwidth to see more signal content (harmonics, faster ripples, etc.) on DC rails that could affect data signals, clocks, etc.
The TPR1000 provides a best-in-class integrity solution for power integrity and validation engineers in the high speed (μP), low power (mobile) and switched-mode power supply markets. The probe is designed to offer the lowest noise with high bandwidth at 60 V offset, flexible connectivity options to cover customers challenges, and software packages to cover the digital power management market.
Connectivity Using Probe Accessories
The available probe accessories provide solutions for reliable and repeatable power rail measurements.
Country of Origin | Germany |
---|---|
Brand | Tektronix |
Condition | NEW |
- 1 - 1 GHz, Single-Ended TekVPI Power-Rail Probe
- 1 - 1.3 m SMA to MMCX Standard Cable
- 1 - 1.3 m SMA to SMA Standard Cable
- 1 - Square Pin Y-leads
- 1 - Clamp
- 1 - U.FL Connector
- 1 - MMCX to Square Pin Adapter
- 3 - Solder Micro-Coax Tips
- 3 - Solder Flex Tips