The TREND Networks (formerly IDEAL Networks) R150001 LanXPLORER Pro Network Troubleshooter with Bandwidth Monitoring and Performance Diagnostics is a hand held tester for analyzing and diagnosing problems in networks, cabling and Ethernet devices using copper, fiber and Wi-Fi interfaces.

Using the LanXPLORER Pro (R150001) in-line and end point modes, IT Technicians can pinpoint issues that are unable to be found with management software as it physically connects to the point of interest instead of scanning the entire network.

LanXPLORER Pro (R150001) does not examine the contents of the data being analyzed, therefore personal and confidential information will remain confidential.

Diagnostic reports can be saved in PDF format and shared with colleagues and clients using the free TREND AnyWare™ app and a mobile device.

Tests

Voice over IP (VoIP) - Monitor Quality of Service (QoS) in real time using In-Line Mode.

Quality of Service (QoS)

Quality of Service (QoS) is measured in real time when LanXPLORER Pro (R150001) is connected in-line between a VoIP phone using SIP (Session Initiation Protocol) and the network. QoS metrics include jitter, delay, total packets, packet loss, source/destination IP addresses and port number. With standard SIP, signalling processes are shown including call pick up, phone number of both phones and duration.

Wi-Fi Testing - Resolve issues on Wi-Fi network and reduce downtime

Wi-Fi Site Survey

As well as using the Wi-Fi interface (2.4/5GHz 802.11a/b/g/n/ac) to connect and troubleshoot the network, the LanXPLORER Pro can perform a Wi-Fi site survey that displays the access point ID, signal strength (dBm), Signal to Noise Ratio (SNR), channel and encryption status. Quickly identify causes of slow Wi-Fi networks or connection issues, such as overlapping Wi-Fi channels or wrong SSID setup. Identify top wireless bandwidth consumers and total aggregate bandwidth consumption (overloaded access point) when connecting the LanXPLORER Pro between wireless access point and the network.

Diagnose Ethernet Issues

Ethernet Device Diagnostics and Troubleshooting using In-line Mode (Copper)

The in-line feature allows monitoring of network traffic between any two devices on the network to diagnose Ethernet issues that cannot be detected by software tools running on a PC or managed switch.

Top 10 Talkers and Listeners

Identifies top 10 bandwidth consuming devices (both transmitting and receiving) on the network to help troubleshooting, e.g. connect between core switch and the internet router to monitor total incoming and outgoing internet bandwidth consumption and identify top 10 bandwidth consuming devices.

Traffic Statistics

Monitor Min/Max/AVG throughput in Mb/s, packet count, frame size and Ethernet protocols.

VLAN Detection

LanXPLORER Pro (R150001) automatically detects VLAN ID's.

Top 10 Talkers and Listeners

Traffic Statistics

VLAN Detection

Network Diagnostic and Troubleshooting using End-Point Mode (Copper, Fiber and Wi-Fi)

The end-point feature is used to monitor and examine the LAN when connected directly to a network port or a mirrored port.

NETMAP/NETVERIFY

NETMAP/NETVERIFY

This function performs a scan of the entire network to identify all active devices by IP address, MAC address and host name which can be saved and compared to future NETMAPs to identify new or removed network devices, or changes in network configuration.

Network Conflicts

Network Conflicts

LanXPLORER Pro (R150001) identifies the source of network conflicts such as unintentionally adding DHCP servers or devices using duplicate IP addresses.

Network Discovery

Connect to active network ports or Ethernet devices to verify network status and connectivity.

Detection of potentially misconfigured devices

LanXPLORER Pro (R150001) identifies devices that are generating network errors or degrading network performance, e.g. computers infected with malware creating broadcast storms that may disable or congest a network.

IEEE 802.1x

IEEE 802.1x

Use the 802.1X protocol to log onto networks secured by this standard, avoiding unnecessary security complications and lengthy project delays (802.1X is a standard for port-based Network Access Control (PNAC)).

Power over Ethernet (PoE) Testing

PoE Monitoring

PoE Monitoring

Using the in-line mode, LanXPLORER Pro (R150001) monitors the voltage and current used at the device.

PoE/PoE+ Load Test

PoE/PoE+ Load Test

Performs PoE/PoE+ load tests to determine the maximum power available to a PoE device at its installed location.

IP Camera/CCTV Diagnostics and Troubleshooting using In-line Mode (Copper)

In-line Mode (Copper)

Connect between network and NVR (Network video recorder) to identify IP address, host name and bandwidth consumption of each camera. Connect between individual IP camera and the network to monitor bandwidth and power consumed using PoE.

Cable Testing (Copper and Fiber)

The LanXPLORER Pro (R150001) offers a series of tests to aid troubleshooting.

Copper Cabling Tests

Copper Cabling Tests

-Wiremap test for open, shorts, miswires and split pairs to TIA-568 standard

-Distance to fault using TDR technology (copper only)

-Ability to identify and trace cables with a compatible amplifier probe (62-164)

-Port blink to visually trace cable from work area outlet to network switch

Fiber Cabling Tests

Fiber Cabling Tests

-Optical power indication (with compatible SFP modules)

-Port blink to visually trace cable from work area outlet to network switch

-Check the fiber SFP characteristics including the vendor name, model number and optical power level

Custom Wiremap

Custom Wiremap

LanXPLORER Pro (R150001) provides an extended list of wiremap templates for common Ethernet cable types including CAT 6A/7A/8, and non-Ethernet cable, such as Profinet, ISDN and Deutsche Bahn (German Rail system).