Triplett TEV200
Electric Vehicle Probe Kit, 230V/400V 3-Phase
TEV200
TEV200
Triplett TEV200
Electric Vehicle Probe Kit, 230V/400V 3-Phase
TEV200
TEV200
The Triplett TEV200 Electric Vehicle Probe Kit plugs directly into users Digital Multimeter, Clamp Meter or Multifunction Tester (MFT). This unit also allows users to perform measurements such as voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance and more.
- Input Voltage: 230V/400V, 3 Phase, 50Hz/60Hz
- Measurement Category: CAT II 300V
- Mains Socket Rating: Maz 10A
- Operating Temperature: -4°F to 104°F
- Plugs directly into Digital Multimeter (DMM), Clamp Meter/Multifunction Tester (MFT)
- Simply connects by wire (Standard Male Banana Type) between EVSE charging point (Type-2 connector), plus measurement inputs of DMM, Clamp, MFT
- Input Voltage: 230V/400V, 3 Phase, 50Hz/60Hz
- CP Simulation: States A, B, C
- PP Simulation: Setup internally to 20 A
- Measurement Category: CAT II 300V
- Mains Socket Rating: Maz 10A
- All wires of charging connector are available: L1, L2, L3, N, PE, CP, PP
- Allows users to perform typical measurements: voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance, low ohm measurements, line/loop impedances (If supported by measuring input device)
- Built-In Control Pilot (CP) State (Vehicle Simulation Switch)
- Different vehicle states can be simulated, Vehicle states are simulated with different resistances connected between CP, PE conductors
- CP Signal output terminals: Use oscilloscope to check waveform, plus amplitude of CP signal
- CP Error “E” simulation: Simulate behavior of station when there is established short circuit between CP, PE
- Complies with EMC Directive (2014/30/EU), Low Voltage Directive (2014/35/EU), EN61010-1 standards
- Includes: (1) IEC62196-2 Type 1 female to male adaptor/converter, plus pouch case2196-2 Type 1 female to male adaptor/converter, plus pouch case
- Input Voltage: UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 208 V, 60 Hz (three-phase system), UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 240 V, 60 Hz (single-phase system), ±10% voltage fluctuations from nominal
- EV Connector (EVC-13): SAE J1772 (Type 1, 5P single phase) for measuring purpose, adapter SAEJ1772 to NACS for measurement purpose
- Operating Temperature: -4F to 104F
Control Pilot (CP) State (Vehicle Simulation)
Vehicle State: A- Electric vehicle not connected
- CP/PE Resistance: Open (∞)
- Vehicle State: ±12V at 1KHz
- Electric vehicle connected, not ready to charge
- CP/PE Resistance: 2.74 K
- Vehicle State: +9V/-12V at 1KHz
- Electric vehicle connected, ready to charge, ventilation not required
- CP/PE Resistance: 882Ω
- Vehicle State: +6V/-12 at 1KHz
- CP Error
- CP/PE Resistance: 0Ω
- Vehicle State: 0V
The Triplett TEV200 Electric Vehicle Probe Kit plugs directly into users Digital Multimeter, Clamp Meter or Multifunction Tester (MFT). This unit also allows users to perform typical measurements: voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance, low ohm measurements, line and loop impedances (if supported by the measuring input device). In addition, this unit easily connects by wire (Standard Male Banana Type) between the EVSE charging point (Type-2 connector) and the measurement inputs of the DMM, Clamp or MFT. All wires of the charging connector are available: L1, L2, L3, N, PE, CP and PP. The built-In Control Pilot (CP) State (Vehicle Simulation Switch) can simulate vehicle states with different resistances connected between CP and PE conductors. Users can use the CP Signal output terminals to connect their oscilloscope to check the waveform and amplitude of the CP signal. CP Error “E” simulates the behavior of the station when there is an established short circuit between CP and PE. The Probe Kit complies with EMC Directive (2014/30/EU), the Low Voltage Directive (2014/35/EU), and EN61010-1 standards.
| Brand | Triplett |
|---|---|
| Condition | NEW |
- 1 - Type 1 Female-to-Male Adapter/Converter, IEC62196-2
- 1 - Pouch Case
- 1 - Female-to-Male Adaptor/Converter, 2196-2
